EnGenius ECB9500 Access Point Firmware 2.2.9

Wireless N 300Mbps Access Point / Bridge / Repeater / Router with Gigabit & 802.3af PoE

HARDWARE SPECIFICATIONS:
MCU: RT2880, 266MHz
Memory: 32MB SDRAM
Flash: 8MB
Physical Interface:
LAN One 10/100/1000 Gigabit Ethernet
Reset Button
Power Jack
WPS Push Button (Wi-Fi Protected Setup)
LED’s Status:
Power (Status)
LAN (10/100/1000Mbps)
WLAN (Wireless Connection)
Power Requirements:
Power Supply: 90 to 240VDC ± 10% 50/60Hz (Depends on different countries)
Active Ethernet: (Power-over-Ethernet, IEEE 802.3af) 48VDC/0.375A
Device: 12V/1A
Regulation Certifications: FCC Part 15/UL, CE

RF SPECIFICATIONS:
Frequency Band: 2.400–2.484GHz
Media Access Protocol: Carrier Sense Multiple Access with Collision Avoidance (CSMA/CA)
Modulation Technology: OFDM: BPSK, QPSK, 16-QAM, 64-QAM, DBPSK, DQPSK, CCK
Operation Channels: 11 for North America
Receive Sensitivity (Typical):
IEEE 802.11n
MCS8 @ -91dBm
MCS15 @ -74dBm
IEEE 802.11g
6Mbps @ -92dBm
54Mbps @ -75dBm
IEEE 802.11b
1Mbps @ -93dBm
11Mbps @ -91dBm
Available Transmit Power:
IEEE 802.11n/g
19dBm @ 6~9Mbps / MCS9
18dBm @ 12~18Mbps / MCS11
17dBm @ 24~36Mbps / MCS13
16dBm @ 48~54Mbps / MCS15
IEEE 802.11b
18dBm @ 1~11Mbps
Antenna: Detachable Omni Antenna x3; RP-TNC Type; Peak Gain 5dBi
Impedance: 50ohm
Frequency Range: 0~6GHz
V.S.W.R.: 1.5 (Max)
Working Voltage: <=500Vrms
Dielectric Withstanding Voltage: <=1500Vrms
Insulation Resistance: >=5000Megohms
Contact Resistance: Center contact 1.5Milliohms (Max) / Outer contact 0.2Milliohms (Max)

SOFTWARE FEATURES:
Topology: Infrastructure
Operation Mode: Client Bridge / Access Point / WDS AP / WDS Bridge / Client Router / Router / Universal Repeater
LAN: DHCP Server / DHCP Client
Wireless:
Wireless Mode 802.11b / 802.11g / 802.11n
Channel Selection (Setting varies by Country)
Signal Strength
Bandwidth Selection 40/20MHz
Transmission Rate
802.11b/g: 54, 48, 36, 24, 18, 12, 11, 9, 6, 5.5, 2, 1 in Mbps
802.11n

Security:
WEP Encryption 64/128bits
WPA Personal (WPA-PSK using TKIP or AES)
WPA Enterprise (WPA-EAP using TKIP)
802.1x Authenticator
802.1x Supplicant MD5/TTLS (Client Bridge & Client Router mode)
Hide SSID in Beacons
Multiple SSID with 802.1q VLAN Tagging (up to 4 SSID)(Access Point mode)
MAC Filter (Access Point mode)
WLAN L2 Isolation (Access Point mode)
Wireless STA (Client) Connected List
QoS: WMM

MANAGEMENT:
Configuration: Web-Based Configuration (HTTP) / Telnet
Firmware Upgrade: Upgrade Firmware via Web Browser; Keep Latest Setting When Firmware Update
Administrator Setting: Administrator Password Change
Reset Setting: Reboot / Reset to Factory Default
System Monitoring: Status, Statistics and Event Log
SNMP: v1, v2c
MIB: MIB I, MIB II (RFC1213), and Private MIB
Traffic Measurement: Per Interface
Bandwidth Measurement: IP Range & Bandwidth Management
Backup & Restore: Settings Through Web

ENVIRONMENT & PHYSICAL:
Temperature Range: Operation 0°C to 45°C (32°F to 113°F) / Storage -20°C to 70°C (-4°F to 158°F)
Humidity (Non-condensing): 5% ~ 95% Typical
Dimensions: L: 4.92” (125mm) x W: 4.25” (108mm) x H: 1.22” (31mm)
Weight: 0.77lb. (350g)

Please do not forget to check with our site as often as possible in order to stay updated on the latest drivers, software and games.

Note: Try to set a system restore point before installing a device driver. It will help you restore system if installed driver not complete.